manufacturer of nickel alloy, stainless steel, tool steel, alloy steel

Master Alloy

Nickel-based alloy · Master alloy · Remelt stock

Master Alloy: Ingot, Bar and Atomization Rod

Six grades, three forms, one supply point. Master alloy is the heat that has not become a part yet: cast into ingots for a crucible, drawn into bar for a remelt shop, or machined into an electrode for a powder atomizer. The pages below are organised by what you are going to do with the metal, not by trade name.

6
Grades in the first batch
Ø30–250 mm
Bar and rod range
5–25 kg
Standard ingot weights
EN 10204 3.1
With gas analysis
Three supply forms of master alloy: ingot, bar and atomization rod
Master alloy is supplied in three forms. The operation decides which one, and the same heat can be certified against any of them.

Start from the operation, not the grade

Most enquiries we receive open with a grade name and a weight. The form is decided later, usually after one exchange that could have been avoided. The three routes below cover what master alloy is actually used for; each one carries different size tolerances, different surface requirements and a different set of acceptance tests.

If you are going to You need What decides the specification
Investment casting or remelting in a VIM furnace Ingot (5/10/25 kg) or cut-to-length bar Crucible capacity, charge weight per heat, whether the furnace can take a 1 m bar
Atomising powder (PREP, VIGA, EIGA) Atomization rod, machined and end-faced Clamp geometry, rod diameter and length, nose angle, surface roughness, oxygen limit
Drawing wire or re-melting for a weld consumable Drawing stock or fine bar Diameter tolerance, coil or straight length, surface condition, drawing reduction

If the operation is not on this list — for example a casting house that remelts in an open induction furnace — say so in the enquiry. The recommendation changes, and so does the grade of cleanliness you actually need to pay for.

The six grades in this batch

Grade Equivalent Where it is used Form
K418 IN-713C / N07713 / 2.4671 Turbocharger wheels, valve bodies, industrial castings Ingot, bar
K438 IN-738LC class / N07738 Gas turbine blades and vanes, hot-corrosion service Ingot, bar
K417G IN-100 class (lower Co) Aero and industrial turbine blades, nozzle segments Bar
IN718 / GH4169 N07718 / 2.4668 Atomization rod for LPBF, EIGA, VIGA, PREP powder Rod
IN625 / GH3625 N06625 / 2.4856 Atomization rod for corrosion-resistant powder Rod
CoCrMo ASTM F75 / Stellite 21 Dental and orthopaedic casting Ingot

Each product page gives the size matrix, the chemistry window, the gas and inclusion limits, the test-bar acceptance values and the melting routes we can quote. None of the pages carries a figure: master alloy is quoted against a grade, a size, a melting route and an inspection scope, and those four answers change the number by a factor of two.

What sits behind the pages

We supply under our AS9120B distribution quality system. Melting is done by qualified VIM, ESR and VAR shops in China; the mill and the heat number are disclosed on the certificate, and on request before the order is placed. That distinction matters to aerospace customers, who audit the melt shop and the distributor separately, and it is the reason we do not describe ourselves as a melting house.

  • Routes — VIM only, VIM+ESR, VIM+VAR, VIM+ESR+VAR, quoted against the gas limit you write
  • Certification — EN 10204 3.1 as standard, with gas analysis and trace-element report; third-party testing (SGS, BV) arranged at cost when the end customer asks for it
  • Traceability — heat number stamped on the end face, repeated on the MTC and on the crate
  • Packing — rust preventive, VCI wrap, crate or wooden case, ISPM 15 heat treatment for export
  • Lead time — confirmed per order against the melt schedule, not published as a fixed number

Read this before you write the purchase order

Three of the eight technical articles already on the site explain why master alloy enquiries go wrong, and they are worth ten minutes before a specification is fixed:

Enquiry

Six grades, one enquiry — send the operation first
  • Operation — casting, atomising or drawing
  • Grade and acceptance standard — GB/T 14992, GJB 5512.1, AMS or your drawing
  • Form, size and single weight — including the crucible or clamp it has to fit
  • Gas and trace-element limits, with the sampling position
  • Certificate, test-bar arrangement and delivery port

Email [email protected]  ·  WhatsApp +86 178 7358 1838  ·  or use the form below.

FUSHUN METAL · AS9120B · EN 10204 3.1 with the heat number.

The grades in detail

Form, chemistry, gas limits and test-bar acceptance for each grade.

About Us

Founded in 1998, FuShun covers an area of 3000 square meters, annual sales volume of 20000 tons. We are engaged in the manufacture and export of Tool Steel, Nickel Alloy, Stainless Steel and other special steel products…,View more content About Me.

Contact Lists

General Manager: Ms. Florence

[email protected]

Get A Free Quote!

Find your steel grade and get a quote today.

NOW Send Your Inquiry To : [email protected]

x